概要 の 使用法 スキル の マルチメーター 入力 家庭用 電化製品 メンテナンス
When using a multimeter, attention should be paid to:
1) 識別 機能 の 各 範囲 の マルチメータ
2) 測定 3 から 4 抵抗 および 記録 それら
3) 測定 AC 電圧 および 記録 それ
4) 測定 DC 電圧 および 記録 それ
1) デジタル マルチメータ
オン the マルチメーター, you will see a conversion knob as shown in the figure, which refers to the gear position of the secondary quantity
V -: 参照 DC 電圧 測定 ギア
MA: 参照 から ギア 位置 用 測定 DC 電圧
Ω (R): 参照 から the ギア 使用済み から 測定 抵抗
HFE: 参照 から ギア 使用 から 測定 抵抗
赤 ペン の マルチメーター 示す 正 極 の 外部 回路, および 黒 ペン 示す 負 極 の 外部 回路
利点: 反 磁気, 便利 および 正確 読み取り (デジタル ディスプレイ)
2) 機械式 マルチメータ
外観 の a 機械 マルチメーター は やや 異なる から それ の a デジタル メートル, しかし 彼らの シフト ノブ は 類似 そして 彼らの ギア 位置 も 基本的に 同じ
On the 機械 時計, you will see a dial as shown in the picture, with eight scales on the dial:
The scale marked with "Ω" is used for 測定 抵抗
スケール マーク 付き "~" is used to 測定 AC/DC 電圧 および DC 電流
スケール マーク 付き "HFE" は 使用済み 測定 the トランジスタ
スケール マーク 付き "LI" 測定 電流 および 電圧 の 負荷
スケール マーク 付き "DB" メジャー the レベル
3) 使用 の a マルチメータ
① デジタル マルチメーター: 前 測定, セット the ギア to the 測定 位置. それ should be note that the range marked on the gear position is the maximum value
② 機械的 マルチメータ: The 方法 for 測定 電流 および 電圧 is the same as the mathal equation, but when 測定 負 電流, the 読み取り must be 乗算 by the value on the gear to 取得 the measured value. For example, the current gear is "X100", the reading is 200, and the measurement question is "200X100=20000} Ω=20}K". The "Ω" scale on the dial is from left to right, from large to small, while the others are from left to right, from small to large
4) Precautions:
① 調整 the "zero point" (のみ 利用可能 in 機械式 時計). 前 使用 the watch, first check if the pointer is pointing to the "zero position" on the left end. If it is not, ゆっくり 回す "開始 ゼロ 位置" 修正 ねじ込み イン 中心 の 時計 ケース 付 a 小 ドライバー to make the point point to the zero position
③ 前 テスト, it is 必要 to 決定 the 測定 内容 and ターン the 範囲 変換 ノブ to the 対応 測定 位置 表示 to 回避 書き込み the メーター ヘッド. if the size of the measured physical quantity is not known, it is is 必要 to start testing from a large range
④ The pen should be 正しく 挿入 into the 対応する ソケット
⑤ 中 テスト プロセス, do not 任意に 回転 the ギア 変更 ノブ
⑥ 後 使用, be sure to 調整 the ギア 変更 ノブ to the 最大 範囲 of AC 電圧
⑦ When 測定 DC 電圧 および 電流, 注意 すべき be 有料 to the 正 および 負 端子 of the 電圧, the flow 方向 of the current, and the correct connection with the probe
